Dashboard

Simply tap on the desired Group to view the I/Os assigned to it.

There are three buttons for control of the Irrigation:

• On -  Tap on this button to turn On the Irrigation.
• Off - Tap on this button to turn Off the Irrigation.
• Auto - If you tap the Auto button, the automation will activate when the conditions are met.

To turn On the Irrigation tap on the button On.

The icon of the Irrigation turns blue and picture of the Irrigation will be changed according to the status On.

To turn Off the Irrigation tap on the button Off.

The icon of the Irrigation is turned grey and picture of the Irrigation is changed according to the status Off.

If you click on the button Auto, you will activate previously created automation for the Irrigation if all conditions are fulfilled from the automation. The icon of the Irrigation turns blue and the picture of the Irrigation is changed according to status open. 

If you click on the button Auto, when some of the conditions from the automation are not fulfilled, the Irrigation will not be activated. The icon of the Irrigation turns grey and the picture of the Irrigation is set according to the status Off. It is necessary that all conditions be fulfilled in order to automation be activated.

Open the Dashboard, find the Irrigation and log press its card.

Tap on Edit tab and edit following form:

• Name - Edit name of the Irrigation.
• Photo - (status On, Off) - Choose the source of the photo.
• Slide to confirm - When it is enabled you will be asked to confirm the desired operation to avoid accidental actions.

Tap Submit/Done.

GOOD TO KNOW:

Irrigation can be edited by long-press the Irrigation card on the Dashboard or tapping it in the I/O list.

You have four options:

• Open Library - The phone’s Library will open. It is recommended to take pictures from the same angle for both irrigation statuses to achieve a complete and consistent view.

• Open Camera - You can take a picture using your smartphone. For a complete and consistent view, it’s recommended to capture both irrigation statuses from the same angle.

• Choose default image - These images are prepared in advance in order  to provide a complete and seamless experience.

• Remove image - Removes existing image.

Slide to confirm feature adds an extra layer of security, preventing accidental actions.

It asks you to confirm your choice once more.

Here's an example of how Slide to confirm feature is applied.

If you want that Irrigation turns Off, tap on Off button and Slide to Turn off from left to the right side.

There are three buttons for control of the Curtains:

• Open - Tap this button to open the Curtains.
• Stop - Tap this button to stop the Curtains.
• Close - Tap this button to close the Curtains.

To open the Curtains tap the button Open.

The icon the Curtains turns blue and picture of the Curtains will be changed according to the status Open.

In order to stop Curtains tap the button Stop, the icon and the picture of the Curtains will be changed.

To  the close the Curtains tap the button Close.

The icon of the Curtains is turned grey and picture of the Curtains is changed according to the status Close.

Open the Dashboard, find the Curtains that you would like to edit and log press its card.

Edit following form:

• Name - Edit the name of the Curtain.
• Photo - Choose a photo for both the closed and opened states of the Curtain.
• Slide to confirm - When it is enabled you will be asked to confirm the desired operation to avoid accidental actions.
• Open Time - Set the time in seconds for the Curtain to fully open.
• Close Time - Set the time in seconds for the Curtain to fully close.

When you are satisfied with the choice tap the button Submit/Done, or if you want to delete Curtains tap button Delete.

Follow next steps.

GOOD TO KNOW:

Curtains can be edited by long-press the Curtains' card on the Dashboard or tapping it in the I/O list.

You have four options:

• Open Library - The phone’s Library will open. It is recommended to take pictures from the same angle for both Curtains' statuses to achieve a complete and consistent view.
• Open Camera - You can take a picture using your smartphone. For a complete and consistent view, it’s recommended to capture both Curtains' statuses from the same angle.
• Choose default image - These images are prepared in advance in order  to provide a complete and seamless experience.
• Remove image - Removes existing image.

Slide to confirm feature adds an extra layer of security, preventing accidental actions.

It asks you to confirm your choice once more.

If you want to Curtain go Close tap the button Slide to Close and slide from the left to the right side.

Opening Time is time in seconds which is needed for the Curtain to open completely.

You have three columns for: hours, minutes, seconds to set opening time.

When you are satisfied tap the button Save.

Close Time is time in seconds which is needed for the Curtain to close completely.

You have three columns for: hours, minutes, seconds to set closing time.

When you are satisfied tap the button Save.

There are three buttons for the control of the Blinds:

• Up - Tap on this button in order to Blinds go up.
• Stop - Tap on this button in order to stop Blinds.
• Down - Tap on this button in order to Blinds go down.

In order to Blinds go up tap the button Up.

The icon of the Blinds turns blue and picture of the Blinds will be changed according to the status Up.

In order to Blinds go down tap the button Down.

Picture of the Blinds and icon will be changed according to the status Down.

In order to stop Blinds tap the button Stop, the icon and the picture of the Blinds will be changed.

Open the Dashboard, find the Blinds that you would like to edit and log press its card, in this case Blinds middle.

Edit following form:

• Name - Edit the name of the Blinds.
• Photo - Choose photos for both the open and closed statuses of the Blinds.
• Slide to confirm - When it is enabled you will be asked to confirm the desired operation to avoid accidental actions.

Calibration - Used to accurately determine the position of the Blinds, either as a percentage or with a slider. Measurements are required to enter the appropriate times for lifting, releasing, and collapsing.

• Lifting time - Measure the time in seconds for the Blinds to fully raise, and enter this value.
• Release time - Measure the time in seconds for the Blinds to fully lower, and input this value.
• Collapse time - Measure the time for the Blinds to collapse or for each lamella to open, and enter this time in seconds.

Tap Submit and Done to save the settings, or if you want to delete the Blinds tap the button Delete.

Follow next steps for more details.

GOOD TO KNOW:

Blinds can be edited by long-press the Blinds' card on the Dashboard or tapping them in the I/O list.

You have four options:

• Open Library - The phone’s Library will open. It is recommended to take pictures from the same angle for all Blinds statuses to achieve a complete and consistent view.
• Open Camera - You can take a picture using your smartphone. For a complete and consistent view, it’s recommended to capture all Blinds' statuses from the same angle.
• Choose default image - These images are prepared in advance in order  to provide a complete and seamless experience.
• Remove image - Removes existing image.

Slide to confirm feature adds an extra layer of security, preventing accidental actions.

It asks you to confirm your choice once more.

Here's an example of how Slide to confirm feature is applied.

If you want Blinds to pull Down tap the button Slide to pull Down and slide from the left to the right side.
 

Lifting time - Measure the time it takes for the Blinds to fully raise and enter this time in seconds.

You have three columns: hours, minutes, seconds to choose lifting time for the Blinds.

Scroll through each one to set lifting time and tap the button Save.

Release time - Measure how long it takes for the Blinds to go down completely and enter the required seconds. 

Tap in the Release Time field to set it.

You have three columns: hours, minutes, seconds to set it.

Scroll through each one to set release time and tap button Save.

Collapse time - Measure the time for the Blinds to collapse or for each lamela to open, and enter the time.

In this step you should choose Collapse Time by tapping in the Collapse Time field.

You have two columns for seconds and miliseconds.

Scroll through each column, set collapse time and tap the button Save.

Doors can be:

• Locked 
• Unlocked 

If Magnet sensor is added to the Doors, Doors can be:

• Open
• Closed

GOOD TO KNOW:

For sliding Doors, when they are in the Open Direction position, their status is Open.

In order to change status of the Doors from the Unlocked - Open to Locked - Close tap on the card of the desired Doors and status will be changed.

Icon of the Doors and picture will be changed according to status Locked - Close.

In order to change status of the Doors from the Locked - Closed to Unlocked - Open to tap on the card of the desired Doors and status will be changed.

Icon of the Doors and picture will be changed according to the new status Unlocked - Open.

Open the Dashboard, find the Door that you would like to edit and long press its card.
 

Edit following form:

• Name - Edit name of the Doors.
• Change picture - Choose the source of the picture for each status of the Doors.
• Slide to confirm - When it is enabled you will be asked to confirm the desired operation to avoid accidental actions.
• Timeout - It shows for how long the Doors will be Open in auto mode.

Tap Submit/Done.

Follow next steps for more details.

GOOD TO KNOW:

Doors can be edited by long-press the Doors' card on the Dashboard or tapping them in the I/O list.

You have four options:

• Open Library - The phone’s Library will open. It is recommended to take pictures from the same angle for both Doors statuses to achieve a complete and consistent view.
• Open Camera - You can take a picture using your smartphone. For a complete and consistent view, it’s recommended to capture both Doors' statuses from the same angle.
• Choose default image - These images are prepared in advance in order  to provide a complete and seamless experience.
• Remove image - Removes existing image.

 Choose Timeout - scroll through columns for the Hours, Minutes, Seconds.

Tap Save button.

Long press the card of the Brightness sensor, in this case, the Hall Brightness sensor.

Edit the following form:

• Name - Edit the name of the Brightness sensor.
• Photo - Choose the source of the photo.

Tap the Submit/Done.

GOOD TO KNOW:

Brightness sensor can be edited by long-press the Brightness sensor card on the Dashboard or tapping it in the I/O list.

Tap photo of the Brightness sensor.

You have three options:

• Open Library - This opens the phone’s Library.
• Open Camera - Take a picture using your smartphone.
• Choose Default Image - These images are prepared in advance in order  to provide a complete and seamless experience.
• Remove image - Removes existing image.